Home › Forums › General › Using Ctrlr › slider/knob/dropdown multisysex
- This topic has 6 replies, 3 voices, and was last updated 9 years, 6 months ago by zeoka.
-
AuthorPosts
-
October 1, 2014 at 9:22 am #29870
Hello everyone,
i want to program a knob/slider/dropdown which changes fx on mc909 via sysex.
Ctrlr is used as VST and the knob mapped to one control change.the purpose of that panel element should be, that it sends different sysex messages per different value of cc mapping.
Example:
host cc parameter 0-09->ctrlrVST->sysexA
host cc parameter 10-19->ctrlrVST->sysexB
..
host cc parameter 120-127->ctrlrVST->sysexYWhats the best panel element to use for that,
for it acts like a cc to multisysex ?
how to configure?greetings
- This topic was modified 9 years, 6 months ago by mdma. Reason: wrong forum category
October 1, 2014 at 11:35 am #29872Several ways
you could link a modulator(cc) to another(sysex) for example
also there some specials bytes in the sysex editor that you can may be change the sysex dynamically
You could may be show us sysex’s you need.
There is also a “controller” feature that seems it’s good for you ….October 1, 2014 at 1:16 pm #29877If you plan on controlling an external device from your host using Ctrlr as a bridge, you don’t need to translate CC->Sysex
the host will modulate your Ctrlr knobs without any CC parameters needed, the internal VST protocol will deal with that, you need to assign your sysex to whatever UI elements you like. Unless you want some other external gear that transmits CC to control your other gear that accepts SysEx with a Ctrlr as a translator, you don’t need any special tricks.
If however you want that sort of translation platform then it gets complicated.
October 7, 2014 at 10:29 pm #30252thank you both for reply!
zeoka:(taken from mc909 editor)
mfx1 on :F0 41 10 59 12 01 00 00 01 7D F7
mfx1 off:F0 41 10 59 12 01 00 00 01 7E F7
mfx1 parameter fx type:
00 through = F0 41 10 59 12 01 00 00 01 7E F7
01 stereoeq= F0 41 10 59 12 10 00 02 01 6D F7
02 spectrum= F0 41 10 59 12 10 00 00 02 6c F7
03 enhancer= F0 41 10 59 12 10 00 02 00 03 6B F7
04 isolator= F0 41 10 59 12 10 00 02 00 04 6A F7
..
38 gatedrev= F0 41 10 59 12 10 00 02 00 26 48 F7
roland mc 909 uses checksum i read
I dont know exactly how to calculate that at the moment.
only can give you calculated-end-message from sysex-editor of mc909
is that message enough anyway?atom:iam a total knoob! is this possible?
in this case fe. a knob 0-38 steps, sending 39 different sysex,1.)using ctrlr as vst(atomation+randomizing cc value)
2.)i have quneo midicontroller, wouldn t that work? midilearnin host, -knob cc ctrlr, cc quneo=happy controlling of hardware with hardware, or not that easy?
- This reply was modified 9 years, 6 months ago by mdma.
October 8, 2014 at 9:50 pm #30310Hi
The byte just before the end byte F7 is the checksum
The simplier way is put z5 as byte in the sysex editor of the modulator
It’s strange that THRU and off are the same param
On my roland 0n/off and 00:THRU are 2 different params
strange that length of sysex is different for the same param
it looks like you just have to put f0…xx z5 f7 in the sysex editormay be you could rely the quneo to the daw (cc) and ctrlr to mc909 (sysex&cc)
that way you control the mc with quneoOctober 9, 2014 at 1:43 pm #30360Hallo and thank you!zeoka you are right! theres a typo-mistake(4) and they are also different
F0 41 10 00 59 12 01 00 00 01 00 7E F7 mfx1:off
F0 41 10 00 59 12 01 00 00 01 01 7D F7 mfx1:on
F0 41 10 00 59 12 10 00 02 00 00 6E F7 00:through
F0 41 10 00 59 12 10 00 02 00 26 48 F7 38:gated reverbit looks like you just have to put f0…xx z5 f7 in the sysex editor
dont understand completely the “tockens” now[F0 41 10 00 59 12] 10 00 02 00 26 6D F7
[(1) (2) (3) (4) (5) (6)] address data checksum (7)would become what ?:
[F0 41 10 00 59 12] 10 00 02 ?? ?? z5 F7————————————
My question was how to configure in ctrlr:
my thought behind: i dont want to use a select-field(ui-combo with combo content i saw)…
a slider/knob with parameter intervals ->sending different sysex.
is it really only sysex-formula?
what is multi-list for?October 9, 2014 at 3:32 pm #30378F0 41 10 00 59 12 01 00 00 01 xx z5 F7 uibutton
and
F0 41 10 00 59 12 10 00 02 00 xx z5 F7 uislider, set the min val 0 max val 38
if you use uifixedslider (to display custom values like THRU…etc) you don’t need to
set min/max values. judt type values in the slider content property
imo it’s better to use combo or listbox to select an effect -
AuthorPosts
- The forum ‘Using Ctrlr’ is closed to new topics and replies.