brunello

Forum Replies Created

Viewing 4 posts - 1 through 4 (of 4 total)
  • Author
    Posts
  • in reply to: Roland MKS-50 Advanced #118889
    brunello
    Participant
      • Topics: 1
      • Replies: 4
      • Total: 5

      Hi there,this works well for me:
      I’m using Ctrlr with MKS 50 panel into Ableton 9,5+ with an Alfa Juno 2 synth as keyboard .

      Once I’ve armed an external instrument track with a CTRLR + MKS 50 istance, I start recording then from chain track I move each modulator i need clicking on and moving just a little bit the corresponding slider over the MKS 50 panel.At this point you’ll see the little triangle below each modulator you’ve moved turning to red and from now on you can tweak with the panel sliders recording every move.You can automate just only slider or all .it just depends on what you need.Finally I saved the CTRLR Panel configuration.

      in reply to: Ableton Live Plug-In Configure Mode? #118674
      brunello
      Participant
        • Topics: 1
        • Replies: 4
        • Total: 5

        Hi I discovered this great panel for MK-50 so first of all thanks to the author for his job.
        I’m learning to use it with my Alfa Juno 2 following the steps which Jasefos clearly explained and everything is working fine.The only thing I can’t understand is that when I move the sliders on the panel I can modify the sound of Juno while i can’t record this changes on envelopes in the Live track.If I try the same tweaks with the modulators in the ctrlr track’s chain i can record it on the ableton envelope.It’s like the panel can’t communicate with Ableton but directly with the Juno synth .In few words I wish to record in Ableton the panel sliders movements .
        Any tip?
        Thanks
        Roland Alfa Juno 2 Saffire 24 DSP

        in reply to: Roland MKS-50 Advanced #118658
        brunello
        Participant
          • Topics: 1
          • Replies: 4
          • Total: 5

          Hi Bomma, and first of all thanks for your panel.You’ve made a great job!I’m just messing around with my Alpha Juno 2 and your Ctrlr Panel finding this issue:
          I’m using the panel into Ableton Live so i created a midi track for CTrlr and an audio track feeded by the the Alpha Juno from the outputs of my Mackie. In the Arrangement view of Ableton if I select with the mouse the Ctrlr midi armed track and play any note the Volume is very low while if i select another any audio or vst synth track,letting armed the CTrlr midi track the Volume is much higher.It seems like when the panel is open the volume goes down.I’m wondering if I’m wrong with routing but can’t figure it out .My soundcard is a Focusrite Sapphire 24 DSP setted on Daw Tracking routing Preset receiving Mackie output on channells 1-2. Hoping I was’nt too confusing in my explanation Have you any advice about it?

          in reply to: Roland MKS-50 Advanced #69827
          brunello
          Participant
            • Topics: 1
            • Replies: 4
            • Total: 5

            Hi Bomma,first of all thanks for your nice and very useful programmer.I’m currently using it with Ableton Live 9 and eveything works fine except for the fact that alpha juno plays sounds even when I play different instruments with different channels in any project. EG: When i play the alpha juno by your au programmer on his midi channel i only listen to, it but if i change track and i play any ableton instrument the alpha juno overdub it like the local control were ON even if it’s setted off. Where
            I’m wrong?
            Thanks
            Bruno

          Viewing 4 posts - 1 through 4 (of 4 total)
          Ctrlr