Jomox AirBase 99

Jomox AirBase99 Midi Controller

Basic panel with all the features supported with Airbase99 firmware 1.15.

Airbase99 settings for full funtionality:

  • Under MIDI Menu (Master Menu parameter PLAY must be off to access MIDI menu):

    setting: SnpSh ON (send program dump on startup and programchange events)
    setting: TxCtr ON (send controller values when changing values on device)

Restrictions:

  • Bank changes do not change the program, a program change needs to be executed with a bank change.(since fw 1.15)
  • To select the Kits # 128-255 in Bank 000 – 003, send the bank select in advance by using the values 1, 3,
    5 or 7. These uneven controller values address memory slots 128 – 255 of the desired bank. The values 0, 2, 4 and 6 correspond to the lower half of the specific bank.
    An example: Bank 000 Kit 200 is selected by using Bank Select = 1 and Prog Change = 73 (200 – 127 = 73)
  • When changing a program a programdump with all the controller values is sent to the panel. But the following controls are not sent and therefore not updated:
    -for handclap, rimshot,crash, ride, hihat: the sample selection.
    -for hihat: the source selection.
    These controls are not in sync with your device after a program change.
  • Button “Save on device” just sends the store cc (CC=62 value=64) value to the Airbase99.

Downloads

Version: 0.5
Jomox_Airbase99-0_5.bpanelz  downloads: 5

Novation X-Station Voice Editor

Here is Novation X-Station voice editor / librarian.

What can it do:

  • Send / receive almost all the parameters via SysEx / MIDI CC messages
  • Save / Load MIDI Bulk SysEx dump files to / from X-Station
  • Save / Load single programs  as *.syx files
  • Receiving MIDI bulk dumps directly from device

This panel have some limitations – for example after “offline” parameters edited, entire patch data is sending via sysex because X-Station not able to control these parameters in realtime.

Current version: 0.4.3 from 14.10.2019

Hope controlling your X-Station with this panel will be fun!

Dreadbox Nyx V2 patch mapper

Patch mapper for the Dreadbox Nyx V2

v1.0 2019-09-29

The panel is a pure patch mapper as the Dreadbox Nyx V2 does not support the load/save of programs or the manipulation of its program parameters by Midi NRPN/CC/Sysex messages.
It will support you in saving and retrieving Nyx V2 patches on your PC but gives you also the possibility to exchange them with other users as they are stored as sysex files.

Features:

  • Dreadbox Nyx V2 interface with similar way of working as actual synthesizer.
  • Top row of support “screens” with old look
  • Visual feedback by using “LED” ring buttons and indication of the value (on change or on click)
  • Envelopes graphs handled by mouse or sliders
  • Load / Save programs from individual .syx files
  • Easy program renaming
  • Display and export of program parameters as text file
  • Ability to describe 9 input/output colored patch cables with different sources/destinations
  • Programs have a name, author, save date and description. They can be associated to a category
  • Browser of the files on the disk
  • Patch sheet tab with patch sheet for Nyx V2 and other gear (external synths/sequencers)
  • Automatic reading of wav files associated to a patch
  • Manual/Automatic reading of any wav file

The manual can be downloaded from Sunny Synth’s OneDrive.

For more info on getting this panel, please contact sunny.synths@gmail.com

Additional pictures:

Dreadbox Erebus V3 patch mapper

Patch mapper for the Dreadbox Erebus V3

v1.0 2019-09-22

The panel is a pure patch mapper as the Dreadbox Erebus V3 does not support the load/save of programs or the manipulation of its program parameters by Midi NRPN/CC/Sysex messages.
It will support you in saving and retrieving Erebus V3 patches on your PC but gives you also the possibility to exchange them with other users as they are stored as sysex files.

Features:

  • Dreadbox Erebus V3 interface with similar way of working as actual synthesizer.
  • Top row of support “screens” with old look
  • Visual feedback by using “LED” ring buttons and indication of the value (on change or on click)
  • Envelopes graphs handled by mouse or classical ADSR rotary encoders
  • Load / Save programs from individual .syx files
  • Easy program renaming
  • Display and export of program parameters as text file
  • Ability to describe 9 input/output colored patch cables with different sources/destinations
  • Programs have a name, author, save date and description. They can be associated to a category
  • Browser of the files on the disk
  • Patch sheet tab with patch sheet for Erebus V3 and other gear (external synths/sequencers)
  • Automatic reading of wav files associated to a patch
  • Manual/Automatic reading of any wav file

The manual can be downloaded from Sunny Synth’s OneDrive.

For more info on getting this panel, please contact sunny.synths@gmail.com

Additional pictures:

 

   

Yamaha AN200

Hello!

Finally I made panel for my Yamaha AN200.

What can it do:

  • Send / receive almost all the parameters via SysEx / MIDI CC messages
  • Manipulate Free EG values
  • Save / Load MIDI Bulk SysEx dump files to / from AN200
  • Save / Load single programs  as *.syx files
  • JayB patch bank embed by default (http://jaybmusic.net)
  • Receiving MIDI bulk dumps directly from device

To make AN200 tweaking more enjoyable – that’s what this panel is created for!

Theoretically, this panel is also compatible with the PLG150-AN card, but it has not been tested, so that’s not sure.

Thanks to the guys Possemo, dnaldoog and goodweather for the tips and tricks!

PS: since this panel is oriented only on a synth part of the device, there are no controls related to the stepsequencer / drum parts.

PPS: it’s still beta, so errors are possible. Please, leave a comment if you are experiencing any problems.

Future plans:

  • Code stabilization
  • Improve AN1X compatibility
Click to expand changelog

 

Changes v 0.6
 
  • Applied dnaldoog”s workaround, fixing startup alert and popup windows odd behaviour
  • Receiving MIDI bulk dumps directly from device now possible
    • After receiving bulk dump you can either save it directly to HDD or load data into panel
  • Settings menu implemented:
    • Added “Send panel data after loading” option
  • Added “Portamento mode” controller
  • Support processing AN1X Edit “MidiEx” bulk dumps
  • Fixed bug in exported VST version, which causes wrong preset name after loading state
  • Fixed Freehand tool right-to-left drawing – there was some inaccuracies which causes broken lines
  • Some minor fixes and slight code review
Changes v 0.7:
 
  • Changed true/false to 1/0 values for “panel loaded” variables
  • Save single program to disk writes current panel state data into preset instead of original preset data
  • Changed some bytes in a sysex formulas – sometimes device ID was “11”, sometimes “10”
  • Added new option – “Send panel data after preset changed” (it was always set to “ON” before)
  • Setting some parameters as not exported to VST host since there is no reason to automate them
Changes v 0.8
 
  • New style controls
  • Removed FreeEG Keytracking knob because it is not used anywhere
  • Adjusted some parameters to fit ImageSlider requirements (hope there was nothing broken during this process…) 
 

Current version: 0.9 from 22.09.2019 

Latest changes:

  • Rewritten bulk dump processing procedure – now it can directly process *.AN2 files
  • AN1X (very limited) experimental support – controls was transferred from experimental panel
  • Fixed some value inconsistencies 
Before you start: this panel using extended instructions set, so you need to turn on extended midi control change mode on your device.
 
Note for AN1X users: to improve compatibility with AN1X model, you can contact me at inteyes.music@gmail.com or leave a comment to provide info about what controls aren’t work. Thanks!
 
I also started adding AN1X-specific controls. I implement them blindly, so test it at your own risk!

To show available AN1X controls, go to Settings -> Set AN1X compatibility mode, then Settings -> Show AN1X-specific controls.

Moog Grandmother patch saver

Patch saver for the Moog Grandmother

v1.3 2019-08-25

The panel is only a patch loader/saver on computer as the Moog Grandmother does not support the load/save of programs by sysex dump exchange. It supports however the manipulation of some program parameters by Midi CC messages but far from all parameters are covered (only the ones described on page 43 of the Grandmother manual).

Features:

  • Moog Grandmother patch saver/loader for PC and Mac
  • Interface with same look as actual synthesizer
  • Bidirectional communication with actual Grandmother synthesizer for all parameters supporting CC# Midi communication (see p43 of the manual)
  • Top row of support “screens” with old look
  • Visual feedback by using “LED” ring buttons and indication of the parameter value
  • Envelope graph handled by mouse or classical ADSR rotary encoders
  • Load / Save programs from individual .syx files
  • Automatic change of all CC# parameters on actual synthesizer at program load
  • Easy program renaming
  • Display and export of program parameters as text file
  • Ability to describe 9 input/output colored patch cables with different sources/destinations
  • Programs have a name, author, save date and description. They can be associated to a category
  • Browser of the files on the disk
  • Patch sheet tab with patch sheet for Grandmother and other gear
  • Patch cables (9 colors)
  • Author and save date
  • External synths
  • Display of current precise parameter value when clicking on rotary encoders
  • Zoom remaining till next session
  • v1.3 Automatic reading of wav files associated to a patch (in file browser)
  • v1.3 Manual/Automatic reading of any wav file (in file browser)

The manual can be downloaded at: https://1drv.ms/b/s!AnIPPW8TKmC9nyvszUfsW1XRCXxM

For more info on getting this panel, please contact sunny.synths@gmail.com

Additional pictures:

 

 

Behringer Neutron patch saver

Patch saver for the Behringer Neutron

v1.2 2019-07-14

This panel can also be called “advanced patch mapper” and is not a full patch loader/saver as the Behringer Neutron does not support the load/save of programs or the manipulation of all its program parameters by Midi NRPN/CC/Sysex messages except for about 40 of them (documented on p27 and 28 of the manual).

In comparison to the Sunny Synths’ Model D and Grandmother panels, this Neutron panel is thus offering much more possibilities of exchange between the synth and your PC or your controller thanks to the addition of the Neutron OS 2.0.

Features:

  • Behringer Neutron interface with similar way of working as actual synthesizer.
  • Panel background adapted based on “Red” overlay from Heinakroon
  • Top row of support “screens” with old look
  • Visual feedback by using “LED” ring buttons and indication of the value (on change or on click)
  • “Intelligent” display following parameters selection: OSC and LFO shape blending, LFO shape order change with or without blend
  • All “hidden” 2.0 available for easy visualization and tweaking
  • Bi-directional behavior when using the synth or a controller (only for parameters indicated in p27 and 28 of the Neutron manual)
  • Envelopes graphs handled by mouse or classical ADSR rotary encoders
  • Load / Save programs from individual .syx files
  • Global settings management
  • Easy program renaming
  • Display and export of program parameters as text file
  • Ability to describe 9 input/output colored patch cables with different sources/destinations
  • Programs have a name, author, save date and description. They can be associated to a category
  • Browser of the files on the disk
  • Patch sheet tab with patch sheet for Neutron and other gear (external synths/sequencers)
  • v1.2 Automatic reading of wav files associated to a patch (in file browser)
  • v1.2 Manual/Automatic reading of any wav file (in file browser)

The manual can be downloaded from Sunny Synth’s OneDrive.

For more info on getting this panel, please contact sunny.synths@gmail.com

Additional pictures:

 

Behringer Model D patch saver

Patch saver for the Behringer Model D

v2.4 2019-07-11

This panel is only a patch loader/saver on computer as the Behringer Model D does not support the load/save of programs or the manipulation of program parameters by Midi NRPN/CC messages except for Global settings that can be transferred to the Model D.

It can thus also be called a “patch mapper”.

Features:

  • Behringer Model D patch saver/loader for PC and Mac
  • Interface with same look as actual synthesizer
  • Top row of support “screens” with old look
  • Visual feedback by using “LED” ring buttons and indication of the parameter value
  • Envelopes graphs handled by mouse or classical ADS rotary encoder and Decay switch
  • Load / Save programs from individual .syx files
  • Easy program renaming
  • Display and export of program parameters as text file
  • Ability to describe 9 input/output patch cables with different sources/destinations
  • Programs have a name, author, save date and description. They can be associated to a category
  • Browser of the files on the disk
  • Patch sheet tab with patch sheet for Model D and other gear (external synths/sequencers)
  • Patch cables (9 colors)
  • Display of current precise parameter value when clicking on rotary encoders
  • Global settings management with automatic/manual send to the Model D synth
  • Panel zoom with memory
  • v2.4 Automatic reading of wav files associated to a patch
  • v2.4 Manual/Automatic reading of any wav file

The manual can be downloaded at: https://1drv.ms/b/s!AnIPPW8TKmC9nX9EnWXixtKtfwyn

For more info on getting this panel, please contact sunny.synths@gmail.com

Additional pictures:

 

 

Do NOT follow this link or you will be banned from the site!